收藏本站
Maximum Ratings
3.13 JTAG/OnCE Interface
Table 13. JTAG/OnCE Interface
Signal
Name
TCK
Signal
Type
Input
State
during
Reset
Input
Signal Description
Test Clock —TCK is a test clock input signal used to synchronize the JTAG
test logic. It has an internal pull-up resistor.
Internal Pull up resistor.
This input is 5 V tolerant.
TDI
Input
Input
Test Data Input —TDI is a test data serial input signal used for test instructions
and data. TDI is sampled on the rising edge of TCK and has an internal pull-up
resistor.
Internal Pull up resistor.
This input is 5 V tolerant.
TDO
Output
Tri-state
Test Data Output —TDO is a test data serial output signal used for test
instructions and data. TDO is tri-statable and is actively driven in the shift-IR
and shift-DR controller states. TDO changes on the falling edge of TCK.
TMS
Input
Input
Test Mode Select —TMS is an input signal used to sequence the test
controller’s state machine. TMS is sampled on the rising edge of TCK and has
an internal pull-up resistor.
Internal Pull up resistor.
This input is 5 V tolerant.
4
Maximum Ratings
CAUTION
This device contains circuitry protecting against damage due to high static voltage or
electrical fields. However, normal precautions should be taken to avoid exceeding
maximum voltage ratings. Reliability of operation is enhanced if unused inputs are pulled
to an appropriate logic voltage level (for example, either GND or V DD ). The suggested
value for a pull-up or pull-down resistor is 4.7 k ? .
NOTE
In the calculation of timing requirements, adding a maximum value of one specification to
a minimum value of another specification does not yield a reasonable sum. A maximum
specification is calculated using a worst case variation of process parameter values in one
direction. The minimum specification is calculated using the worst case for the same
parameters in the opposite direction. Therefore, a “maximum” value for a specification will
never occur in the same device that has a “minimum” value for another specification;
adding a maximum to a minimum represents a condition that can never exist.
DSP56371 Data Sheet, Rev. 4.1
Freescale Semiconductor
33
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SP339EER1-0A-EB BOARD EVALUATION FOR SP339E
SP720ABG TVS ARRAY ESD 14 INPUT 16-SOIC
SP720ABT TVS ARRAY ESD 14 INPUT 16-SOIC
SP721ABG TVS ARRAY ESD 6 INPUT 8-SOIC
SP721ABT TVS ARRAY ESD 6 INPUT 8-SOIC
SP723ABT TVS ARRAY ESD 6 INPUT 8-SOIC
SP723APP TVS ARRAY ESD 6 INPUT 8-DIP
SP724AHTG TVS ARRAY ESD 4 INPUT SOT-23
相关代理商/技术参数
SOURCE INSPECTION 制造商:Vishay Dale 功能描述:FACTORY INSPECTION
SOURCE INSPECTION CHARGE 制造商:Leach International Corporation 功能描述:SUB MINIATURE - Virtual or Non-Physical Inventory (Software & Literature)
SOURCEINSPECTION/SG1549Y-12824 制造商:Microsemi Corporation 功能描述:CURRENT SENSE LATCH - Bulk
SOVEREIGN 10-300 制造商:Fane International 功能描述:Sovereign Series 10" Professional Audio Woofer - 300W RMS
SOVEREIGN 12-200 制造商:Fane International 功能描述:Sovereign Series 12 Inch Prosound Woofer 200W
SOVEREIGN 15-250 制造商:Fane International 功能描述:Sovereign Series 15 Inch Prosound Woofer
SOVEREIGN 15-500 制造商:Fane International 功能描述:Sovereign Series 15 Inch Prosound Woofer 500W
SOVEREIGN 18-500 制造商:Fane International 功能描述:Sovereign Series 18 Inch Prosound Woofer